Solution
The chain bucket elevator manufacturer will take you to understand the daily operation precautions of the bucket elevator
Release time:
2022-04-25 16:58
Source:
The chain bucket elevator manufacturer tells you that the bucket elevator uses a series of hoppers that are evenly fixed on the endless traction member, a continuous conveying machine that vertically lifts materials, and the bucket elevator uses a series of hoppers fixed to the traction chain or tape. The bulk material is transported upwards in a vertical or near-vertical direction. It is divided into three types: ring chain, plate chain and belt. The chain bucket elevator manufacturer tells you that the bucket elevator is a kind of conveying equipment for vertically lifting materials. It has the advantages of simple structure, low maintenance cost, high conveying efficiency, high lifting height, stable operation and wide application range. The driving power is small, and the inflow feeding, induction discharging, and large-capacity hopper are densely arranged. There is almost no material returning and digging when the material is lifted, so the ineffective power is small.
1. We must carry out no-load test operation, and do not install it immediately after full-load operation, which is prone to more serious accidents, such as material head breakage, bearing burnout, etc. Many people may feel less serious, but this is ours The situation seen by the after-sales personnel of the crane should be driven with no load. Therefore, all material in the hopper should be drained before each stop, and then stopped.
2. It is necessary to pay attention to the direction of operation. We have to make sure that the bucket elevator is running forward, i.e. from bottom to top. If the opposite happens, serious problems can arise. on the contrary. The chain bucket elevator manufacturer tells you that if the reverse is reversed, chain derailment may occur, and it is very troublesome to eliminate the derailment failure.
3. The point is to remind our dear users that when you use the bucket elevator to transport, you must work strictly according to the design capacity, and you must not dig our dig very deeply for the sake of instant speed, which will cause us serious problems. Overload or overload, if the overload is serious, too much carton feedback will cause the carton phenomenon, causing the motor to stop or the motor to burn, and the feeding is even. Sudden increases in feed volume are prohibited. The feed volume should not exceed the conveying capacity of the elevator. Otherwise, when the material at the bottom accumulates seriously, it is easy to cause a "stuffy car" accident.
4. Supplement lubricating oil in time. The chain bucket elevator manufacturer tells you that it is very important to lubricate a part of the elevator. For a machine with good lubrication performance, it is very important to achieve good operating results.
5. The chain and hopper should be replaced in time to avoid serious wear or damage. Then this point is also very correct and very important. The chain bucket elevator manufacturer tells you that because the chain and the hopper are consumables, because we can imagine that the hopper is in direct contact with the material, there will be wear and tear, and the chain will continue to drive the chain hopper. Running, well, it's also subjected to a lot of force, so it also causes a lot of wear and tear, so because of the wear and tear, we need to replace it in time.
Previous page
Next page
More solutions
Batching plant bulk material transfer scheme
In batching plant systems, assembled steel silos are often required as intermediate storage containers for ingredients. Bulk materials are transported to these assembled steel silos by bulk trucks, belts, etc., and then conveyed to the weighing scales via screw conveyors, belt conveyors, etc., for mixing.
Factory Bulk Material Storage and Conveying Solutions
Factory bulk material storage and conveying solution: Raw materials arrive at the factory by bulk trucks or other means, and are conveyed to the raw material storage silo via dump-lift or compressed air. They are then transported to the metering equipment via belt conveyor or screw conveyor. After precise metering, they are mixed or bagged, and sent to the finished product storage silo via discharge equipment, or bagged for sale after packaging by an automatic packaging and palletizing machine.
Hydropower project bulk material transfer scheme
New hydropower projects are usually built in relatively remote areas, making it difficult to transport raw materials such as cement, fly ash, and sand and gravel. Large-capacity prefabricated steel plate silos are usually needed for centralized transportation, allowing for a single delivery to cover a longer period. The materials are then directly transported to the point of use via inclined belts, pneumatic conveying, and other methods.
Train Bulk Material Transfer Scheme Diagram
Bulk materials are delivered to the site by train, and then transported via pneumatic conveying/belt conveying/screw conveyors and elevators, etc., to assembled steel silos for storage. From there, they are distributed to various locations in the region by tanker trucks, or connected to a bagging machine for sale as bagged materials, or transported by truck to the point of use.
Port Bulk Material Transfer Station Solution
Bulk materials arrive at the terminal by water, and are then transported to assembled steel plate silos for storage via pneumatic conveying, belt conveying, ship unloaders, bulk truck transfer, chutes, elevators, etc. Afterwards, they are distributed throughout the region by cement tankers or connected to packaging machines for sale as bagged materials.
Mine Bulk Material Storage and Transportation Solution
Ore raw materials are transported through mining to raw material storage silos or stockyards, then transported via conveyor belts to crushing machinery (coarse crushing, fine crushing), and then transported by belt conveyors/hoists or other means to finished product storage silos or processing equipment, finally transported by truck or packaged for sale. If necessary, the crushed granular material is then ground into powder by a pulverizer and transported to the finished product warehouse, then sold via bulk trucks or after packaging.
Xiamen Luwei Prefabricated Steel Structure Co., Ltd.
Scan the code to add us on WeChat.
Zhixiang’s Video Account
Zhixiang Official Account
Xiamen Luwei Prefabricated
Steel Structure Co., Ltd Ltd.
Service Hotline:
Domestic Sales (Manager Wu): 0086 18059271069
International Sales (Manager Tina): 0086 18150889219
Email:sales@xmlwjx.com
Company registered address:
3rd Floor, Office Building, No. 608, Xinxi South Road, Xinxu Town, Xiang'an District, Xiamen City
R&D and Manufacturing Address:
Factory, 2nd Floor, E, No. 608, Xinxi South Road, Xinxu Town, Xiang'an District, Xiamen City
