Image name

Solution


What are the protection contacts of bucket elevator for cement plant


What are the protection contacts of bucket elevator for cement plant, the following bucket elevator for cement plant manufacturers will take you to find out.

Low price bucket elevator for cement plant from China manufacturer
1. Brake oil pressure overpressure protection relay contact: The bucket elevator for cement plant manufacturer tells you that when the brake oil pressure is overpressured, the oil pressure relay contact is closed, on the one hand, it sends out a light signal, and on the other hand, it makes the normally closed contact in the Ac circuit. Head disconnected.
2. Loss of current protection relay contact: It is used for disconnection protection of the depth indicator self-aligning machine, and the car contact is disconnected when the line is disconnected.
3. Contact of dynamic brake voltage loss relay: when the controllable dynamic brake power supply has no voltage or the voltage is too low, the contact will be disconnected.
4. Auxiliary contact of oil opening cover: When the main circuit is overcurrent, the father or other reasons trip the high-voltage circuit breaker, the safety brake contactor is disconnected at the same time, and the bucket elevator for cement plant brakes safely.
5. Over-roll switch contact: disconnect when the lifting container is over-rolled. The bucket elevator for cement plant manufacturer tells you that one set is installed on the derrick and the other set is installed on the depth indicator, which has the same function. In addition, there is a failure of the overwind reset switch, which is used to short-circuit the overwind lift switch that has been touched, so that the AC circuit is connected, and the safety brake is released, so as to release the overwind container. After the container returns to the normal position, the hoist should be disconnected in time, otherwise the over-roll protection will be lost.
6. The brake shoe wears the switch contact: the bucket elevator for cement plant manufacturer tells you that when the brake shoe is excessively worn, the contact will be disconnected. In addition to the protection devices installed in the safety circuit, there are also some protection devices, which do not require the hoist to stop immediately, so that the cycle can be completed, but it is not allowed to start again. The bucket elevator for cement plant manufacturer tells you that the normally open contact of the oil pressure relay is closed when the lubricating oil is over pressure, the normally closed contact of the oil pressure relay is closed when the lubricating oil is under pressure, and the normally open contact of the brake oil overheat temperature relay is closed Wait.

More solutions


Batching plant bulk material transfer scheme

In batching plant systems, assembled steel silos are often required as intermediate storage containers for ingredients. Bulk materials are transported to these assembled steel silos by bulk trucks, belts, etc., and then conveyed to the weighing scales via screw conveyors, belt conveyors, etc., for mixing.


Factory Bulk Material Storage and Conveying Solutions

Factory bulk material storage and conveying solution: Raw materials arrive at the factory by bulk trucks or other means, and are conveyed to the raw material storage silo via dump-lift or compressed air. They are then transported to the metering equipment via belt conveyor or screw conveyor. After precise metering, they are mixed or bagged, and sent to the finished product storage silo via discharge equipment, or bagged for sale after packaging by an automatic packaging and palletizing machine.


Hydropower project bulk material transfer scheme

New hydropower projects are usually built in relatively remote areas, making it difficult to transport raw materials such as cement, fly ash, and sand and gravel. Large-capacity prefabricated steel plate silos are usually needed for centralized transportation, allowing for a single delivery to cover a longer period. The materials are then directly transported to the point of use via inclined belts, pneumatic conveying, and other methods.


Train Bulk Material Transfer Scheme Diagram

Bulk materials are delivered to the site by train, and then transported via pneumatic conveying/belt conveying/screw conveyors and elevators, etc., to assembled steel silos for storage. From there, they are distributed to various locations in the region by tanker trucks, or connected to a bagging machine for sale as bagged materials, or transported by truck to the point of use.


Port Bulk Material Transfer Station Solution

Bulk materials arrive at the terminal by water, and are then transported to assembled steel plate silos for storage via pneumatic conveying, belt conveying, ship unloaders, bulk truck transfer, chutes, elevators, etc. Afterwards, they are distributed throughout the region by cement tankers or connected to packaging machines for sale as bagged materials.


Mine Bulk Material Storage and Transportation Solution

Ore raw materials are transported through mining to raw material storage silos or stockyards, then transported via conveyor belts to crushing machinery (coarse crushing, fine crushing), and then transported by belt conveyors/hoists or other means to finished product storage silos or processing equipment, finally transported by truck or packaged for sale. If necessary, the crushed granular material is then ground into powder by a pulverizer and transported to the finished product warehouse, then sold via bulk trucks or after packaging.